Arnold Grenier asked 1 ปี ago
Fiat 500 Replacement Key Fob
It could be time to replace the battery if your 500 remote key fob is not working. If you do replace the battery but it doesn’t work then the issue is likely to be elsewhere.
United Locksmith specializes in the production of new keys for Fiat 500 Key classic vehicles. We have the tools as well as the parts needed for this service.
Dead Coin Battery
The most frequent reason why your Fiat 500 key fob will not unlock or lock the doors is a dead battery. The key fob is equipped with a coin cell battery which will quickly drain when it isn’t being utilized frequently enough. If your remote started to show signs of weakness such as a loss in range or stopped working completely the battery could be dead.
The battery in the key fob is secured by metal retaining clips. If the clips are not tight, they can create contact problems that will prevent the remote from receiving power. Make use of a flathead screwdriver to remove the retaining clip and then remove the old battery. Be sure to use a replacement battery with the same type of voltage, size, and specification as the original battery.
The exposure to water can cause the key fob to corrode, or even become damaged. Even a quick shower in soapy water can damage the electronic chip inside. Make sure your key fob is dry.
Water Damage
If your key fob isn’t operating properly, it may be due to water damage. Key fobs come with rubber seals that stop them from being damaged by a light rain or splashes of water, but it is vital to keep your keys out of the ocean, pool, and washing machine!
The key fob has an electronic chip inside that sends a signal car’s immobilizer system. This is what allows your 500 to start or lock, Fiat 500 Key however when the chip becomes wet, it’s unable to longer function.
If you want to check whether your key fob still functioning, you can clean the internal electronics using isopropyl or an electronic cleaner. It is best to replace the key fob if it has been submerged into salt water rather than try to repair it yourself.
A replacement fob may cost you some money however, it’s cheaper than having to have your Fiat 500 towed to a dealership and fixed there! You can also fix it yourself by following just a few steps. Make sure you have the correct battery type before you attempt to open your key fob. This task is much simpler than it appears, and you can find step-by-step directions on the internet for nearly any key fob in your car.
Faulty Chip
The chip inside the key fob is in direct communication with the immobiliser on your car to ensure that your vehicle will only start when the right keys are in place. If the chip is damaged or destroyed the car will not start no matter what you do.
Damage to the water or a dead cell battery are the two most frequent causes of the chip being damaged. Regardless of the reason, it is a good idea to leave this work to a locksmith as they can replace the chip for you quickly and at a reasonable cost.
If your key fob will not work after exposure to clean tap or rain water take it off the battery. Wipe down the electronic component using a towel. If the key fob does not function, there is an opportunity that it is damaged components and requires to be replaced.
Some people will visit their dealer if they require a new Fiat fob. But, this can be costly. If you are seeking a cost-effective method to get your Fiat key fob repaired, look no further than United Locksmith. We have the tools and knowledge required to repair your Fiat fob quickly and professionally. way.
Faulty Receiver Module
Fiat key fobs transmit signals of up 50 feet to the vehicle, which will open and close the doors (and start the vehicle for those with automatic transmissions). There are several reasons why the fob may not function. This can be caused by a dead coin-battery, water damage, worn out buttons as well as a receiver issue. signal interference or an issue with the chip.
If the fob was in the pocket of someone who has suffered severe trauma (such as being dropped on the hard floor or washed in the washing machine) it might not be in a position to connect with the Body Control Module (BCM) of the vehicle. The BCM is a security device that will only accept signals from genuine keys.
You’ll have to replace the fob in case this occurs. A professional locksmith will manage the entire replacement process including programming a new key to your 500. In fact, they can offer you a clone key that functions exactly the same way as your original fob (and costs a fraction of the price).